Window Opening Enlargement Services in Orlando, Florida
Window opening enlargement transforms cramped rooms into bright, airy spaces by strategically widening or heightening existing window frames. Bill Morgan inc removes interior drywall, exterior siding, and structural elements while installing temporary support beams, then frames new openings with pressure-treated headers rated for Florida wind loads up to 150 mph. Most enlargements in Orlando neighborhoods like Dr. Phillips, Belle Isle, and Conway add 200-400 square inches of glass per window, increasing natural light by 40-60% and boosting home value by 3-5%.
Our window opening enlargement process begins with structural assessment and permit acquisition from Orange County Building Department, typically approved within 5-7 business days. We install temporary support walls, cut through framing members, reinforce headers with engineered beams, patch exterior weather barriers with DuPont Tyvek, and finish with trim, caulking, and paint. Final inspections verify proper flashing, insulation, and glazing seal integrity before project completion.
What Is Included
When you hire Bill Morgan inc for window opening enlargement, here is exactly what you get:
- Structural engineer assessment and load calculations for window opening size
- Orange County building permits and inspection scheduling
- Temporary support beam installation to maintain roof/floor loads
- Removal of drywall, siding, and existing window frames
- Installation of pressure-treated headers sized for 150 mph wind loads
- New vinyl or aluminum window frames with Low-E glass
- Weather barrier installation with DuPont Tyvek and flashing
- Interior and exterior trim, caulking, and painting to match existing finishes
- Final building department inspection and sign-off
Signs You Need Window Opening Enlargement
- Rooms feel dark despite daytime hours, especially north or east-facing spaces
- Kitchen, bathroom, or living areas lack sufficient natural ventilation and light
- Existing windows are smaller than modern standards for similar home sizes
- Desire for scenic views of parks, lakes, or community golf courses like Timacuan Golf Club
- Home addition or renovation plans that benefit from larger window openings
- Rooms feel cramped or disconnected from outdoor patios or landscape features
- High energy bills due to insufficient daylight reducing daytime lighting loads
- Resale value improvement sought by expanding living spaces visually
Our Window Opening Enlargement Process
Free In-Home Consultation and Structural Assessment
Bill Morgan inc representatives visit your Orlando home (Winter Park, Oviedo, Maitland, etc.) to evaluate window locations, existing framing, and load-bearing status. We measure openings, photograph conditions, and assess exterior siding type and interior wall depths. Consultation typically takes 30-45 minutes and includes preliminary cost estimate.
Engineering Design and Building Permit Application
Licensed structural engineers calculate header sizes, beam capacity, and reinforcement requirements based on window enlargement dimensions and roof/floor loads. Permits submitted to Orange County Building Department within 2 business days; approval typically granted within 5-7 days for standard residential enlargements.
Temporary Support Wall Installation
Before any demolition, we construct temporary support walls using 2x12 lumber positioned 3 feet from the opening to carry loads during framing removal. This step takes 4-6 hours and ensures structural integrity throughout the project.
Demolition and Framing Preparation
Drywall, siding, windows, and deteriorated framing are carefully removed, exposing structural members. Exterior sheathing and weather barriers are removed to prepare for new frame installation. Dust containment using polyethylene barriers keeps debris contained indoors.
Header Installation and Structural Reinforcement
Engineered headers, typically 2x12 or 2x14 pressure-treated lumber with steel plates, are installed above the enlarged opening. Support beams are secured to adjacent studs and floor/roof systems. This stage takes 6-10 hours depending on opening size.
New Window Frame Installation and Weatherproofing
New vinyl or aluminum window frames are installed with proper shimming and leveling. DuPont Tyvek weather barrier is applied around frame perimeter with overlapping flashing at sill and head. Foam sealant and caulk create air-tight seals within 8-12 hours.
Interior and Exterior Finishing
Drywall patches are taped, mudded, and sanded; exterior siding is matched and reinstalled. Interior and exterior trim is caulked, painted, or stained to match existing finishes. Project completion typically occurs within 2-3 days total.
Final Inspection and Building Approval
Orange County Building Inspector verifies proper installation, flashing, insulation, and glazing. Final sign-off confirms compliance with Florida Building Code and permits project closure. Post-inspection walk-through confirms homeowner satisfaction.
Types of Window Opening Enlargement We Handle
- Vinyl double-hung window openings with Low-E glass for energy efficiency
- Aluminum frame picture windows for maximum unobstructed views
- Casement window enlargements with operator hardware for ventilation control
- Sliding glass door conversions from existing smaller windows for patio access
- Bay or bow window installations extending outward 12-18 inches for added interior space
- Transom window additions above enlarged openings to increase ceiling light penetration
- Combination picture and casement openings for mixed aesthetic and functional requirements
Why Orlando Homeowners Choose Bill Morgan inc
Bill Morgan inc has completed 200+ window opening enlargement projects across Orlando, Winter Park, Altamonte Springs, Maitland, Oviedo, and 50+ Central Florida communities since 2005. We employ only Orange County-licensed contractors, maintain General Liability and Workers Comp insurance with $2M coverage, and guarantee all structural work for 10 years. Our projects consistently pass first-time building inspections due to meticulous permit preparation and code compliance; we handle all engineering calculations, permit applications, and final inspections, eliminating homeowner coordination burden. Unlike general contractors, we specialize exclusively in structural modifications, delivering expertise in load calculations, header sizing, and Florida wind-load requirements that protect your home's integrity.
